P0035 Check Engine Light - Hyundai Genesis Forum
 
LinkBack Thread Tools
post #1 of 5 Old 12-31-2018 Thread Starter
Junior Member
 
Join Date: Dec 2018
Posts: 1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
(Thread Starter)
Unhappy P0035 Check Engine Light

Genesis Coupe 2.0t 2013
Mileage: 78,000

I was driving my car one day, and my engine light came up. I took it to O'Reilly and it said P0035. "Turbo Charger Bypass Valve Control Circuit High"

1) Air pressure is coming out of the oil fill cap. (not sure if it's supposed to be doing that)
2) Intake manifold shakes when at idle and driving.

Any suggestions? Thanks.
bk2.chris is offline  
Sponsored Links
Advertisement
 
post #2 of 5 Old 01-01-2019
I'd rather do it myself
 
Red Raspberry's Avatar
 
Join Date: Aug 2009
Location: Flat lands of Illinois
Posts: 18,017
Mentioned: 18 Post(s)
Tagged: 1 Thread(s)
Quoted: 3 Post(s)
Garage

That would mean there is a short to ground in the BOV solenoid wiring. Could mean the solenoid coil is also shorted. Use an ohm meter to test the coil, shorted would be a very low number.

2010 Red 2.0L track

Quote:
If the Pharaohs had duct tape, the Sphinx would still have a nose...."
Red Raspberry is offline  
post #3 of 5 Old 06-15-2019
barely turns a wrench
 
onesight1's Avatar
 
Join Date: May 2010
Location: Erie, PA
Posts: 509
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)

Quote:
Originally Posted by Red Raspberry View Post
That would mean there is a short to ground in the BOV solenoid wiring. Could mean the solenoid coil is also shorted. Use an ohm meter to test the coil, shorted would be a very low number.
Im having this same issue... im desperate.

I replaced both WGA/BOV solenoids with new OEM ones. Still has problem.... how do I check the solenoid coil? is that what's inside those little solenoids? or something else attached to it?

I tried to stick the pins inside the end connectors to the solenoids... and I also cut back and exposed some out the wiring before the connectors. I don't know what #'s im looking for

I tried to get a shop manual- but it doesn't help me much.


I brought it to the shop... just to see if it really was an electrical issue but they instead mentioned turbo vacuum lines ... " we can replace them for an extra $150, on top of the 120$ diagnostic fee " .... if that doesnt do it, its probably the turbo. "

I just told them i'm going to keep troubleshooting it at home....hopefully you give me something I can further look for/ try out. Would be super appreciative.
onesight1 is offline  
 
post #4 of 5 Old 06-15-2019
I'd rather do it myself
 
Red Raspberry's Avatar
 
Join Date: Aug 2009
Location: Flat lands of Illinois
Posts: 18,017
Mentioned: 18 Post(s)
Tagged: 1 Thread(s)
Quoted: 3 Post(s)
Garage

Take the connector off and with an ohmmeter stick the two contacts. Resistance at room temperature should be 28 to 31 ohms. If it is lower, then it will draw too much current and act like a short (0-~3 ohms). P0035 means a short to ground or the voltage being put out by the Engine control relay 12v to control the solenoid is being drawn down to 0V. This is terminal 1 on the solenoid, terminal two would be the variable ground being put out by the ECU.

You should also do the same test with the wire coming harness for the solenoid. With the key off and meter set on ohms test both wires at the connector one at a a time to engine ground. One may give a reading (ground from ECU) but the other, control voltage should show open or infinity. With the key in run terminal 1 should have battery voltage.


2010 Red 2.0L track

Quote:
If the Pharaohs had duct tape, the Sphinx would still have a nose...."
Red Raspberry is offline  
post #5 of 5 Old 06-15-2019
barely turns a wrench
 
onesight1's Avatar
 
Join Date: May 2010
Location: Erie, PA
Posts: 509
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)

Quote:
Originally Posted by Red Raspberry View Post
Take the connector off and with an ohmmeter stick the two contacts. Resistance at room temperature should be 28 to 31 ohms. If it is lower, then it will draw too much current and act like a short (0-~3 ohms). P0035 means a short to ground or the voltage being put out by the Engine control relay 12v to control the solenoid is being drawn down to 0V. This is terminal 1 on the solenoid, terminal two would be the variable ground being put out by the ECU.

You should also do the same test with the wire coming harness for the solenoid. With the key off and meter set on ohms test both wires at the connector one at a a time to engine ground. One may give a reading (ground from ECU) but the other, control voltage should show open or infinity. With the key in run terminal, 1 should have battery voltage.




You have no idea how much I appreciate you.

Will update you this weekend. Im excited to try this.
onesight1 is offline  
Sponsored Links
Advertisement
 
Reply

Related Threads
Thread Thread Starter Forum Replies Last Post
2013 2.0t - Code P0035 BPV - recurrent nightmare rockoo Electrical & Wiring 2013 and up 28 02-22-2016 04:21 PM
P0035 code thrown [email protected] 2.0T Discussion 2013 and up 57 11-02-2013 03:41 PM
Cel: P0035 davidlee92 Electrical & Wiring 2013 and up 6 10-20-2013 04:38 PM
P0035 Jedsred89 2.0T Discussion 2013 and up 6 10-18-2013 05:25 PM
AEM Intake installed...check....Engine bay now looks ugly with rad showing...Check Awesome3.8 3.8 V6 Discussion 2008-2012 18 12-04-2010 09:10 AM


Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Hyundai Genesis Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










User Tag List

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome