Hyundai Genesis Forum banner
help install
1-13 of 13 Results
  1. General Discussion
    Alright, y’all it’s me again. So I’m currently installing dual oil catch cans on my 2010 2.0T. I think I’m doing the install wrong on knowing which is the correct order in which the hoses go in and out of the catch can. I’ll upload some pictures so y’all can see if I’m doing it right or wrong...
  2. Electrical & Wiring 2008-2012
    So I'm looking at getting a byo cluster kit and I have a couple of questions. 1 where would I wire them in using the original gauge cluster wires? Or elsewhere, it's 7 different guages, speed, fuel level, oil temp, coolant temp, rpm, and boost I know how to wire in the boost guage though, the...
  3. Engine
    I have a 2011 3.8 grand touring automatic, I was having problems with the check engine light about a week ago, so i take it to auto-zone for a free light check and i get a P0442 code (small EVAP leak) so im like oh what part should i change, they said the purge valve i said ok i buy it and get...
  4. Exterior 2013 and up
    I've had my genesis for a couple of months and want to install Catback Exhaust. I found one that's not too expensive and just wondering if anyone has used products from this company and how's the installation process to install a Catback exhaust system. Any advice would be appreciated The...
  5. 2.0T Discussion 2013 and up
    I have a stage 1.5 sfr tune, catless exhaust, SRI CAI, and A forge BOV with a yellow spring installed. I am not sure if I should have cap off the opening be hide the BOV. When I didn't hear the BOV as loud as it was with it being opened.. Any advice here? Hopefully one of the links below work...
  6. Exterior 2013 and up
    So I currently own a 2012 3.8 GT coupe, White. I've owned it for 2 years now, and have put nearly 60,000 miles on it. I love this car. However, I bought it just a few months before the 2013's. From the extra power, to the new transmission, direct injection and better paint (white), I've been...
  7. 2.0T Discussion 2013 and up
    Sorry I'm new to all of this so bear with me. First of all yes I did search and found nothing. Ok so I ordered a forge Bob from genracer. It came with a packet that had a couple springs screws and 2 metal disks. I read to use the yellow spring so I put that in but what do you do with the metal...
  8. Wheels, Tires and Brakes 2008-2012
    Hey guys, sorry for the noobish post, but to my defense, I have done my research and found too many inconclusive responses, and not a definite answer. I know very little about wheel & tire fitting, but I want to replace my stock rims on my 2010 2.0t with different ones, and am hoping to not have...
  9. Drivetrain
    Heya: I am in the middle of installing a set of the CP-E differential mounts. -- 2012 2.0T M/T I wrote CP-E whom stated that the mount would fit. However, I am having an impossible time getting the stock driver side diff mount out! I ahve even gone so far as destroying the rubber inside...
  10. Electrical & Wiring 2008-2012
    I just bought RGB footwell LEDs from Diode Dynamics and spliced the positive and negative into the positive and negative of the front cigarette lighter and ground it into a bolt under and to the right of the steering wheel. Every time I turn on the car it blows the fuse for that cigarette...
  11. 3.8 V6 Discussion 2008-2012
    So my car is at the dealer, and because my thermostat stopped working, this caused my radiator to leak in my 2010 Gen Coupe 3.8 with 85,000. This is not covered under warranty, although the transmission was replaced less then 10,000 miles ago, and they left a leaky transmission cooler line and...
  12. Exterior 2008-2012
    Hello everyone, Quick question I am hoping to get some insight on. I had my boyfriend install the rear wing emblem over the weekend and spontaneously it rained about 30 minutes later. He had to drive my car back out to me for an event and decided just to drive it. Afterward, I noticed that the...
  13. South East
    Hey guys.. just got my eibach pro kit springs and hubcentric spacers.. would anyone nearby be willing to help me install? I dont have the tools but will pay to rent if needed. Will pay you as well... name a reasonable price.. its an easy install 1 1/2-2 hrs tops theres directions and even a dyi...
1-13 of 13 Results
Top